vi
: By clipping the line that senses the Push-To-Talk (PTT) switch on the Clarifier circuit and tying it to a constant 8V DC source inside the radio, the Clarifier will remain active during transmission. This allows you to "net" perfectly onto an amateur radio frequency. 3. Microphone Audio & Compression Upgrades
The Ultimate Guide to Icom IC-M700 Modifications The Icom IC-M700 is a legendary marine HF transceiver. Built like a tank, this commercial-grade radio is famous for its reliability. While designed for maritime use, many amateur radio operators and shortwave enthusiasts use it on ham bands.
On the Low-Pass Filter unit (near the PA), locate R28 . This resistor sets the ALC threshold. Replace the stock value (often 22k ohms) with a 50k ohm linear potentiometer in series with a 10k ohm fixed resistor.
If over-modulation or "splatter" becomes an issue after changing microphones, you can adjust the internal Mic Gain potentiometer () and the ALC (Automatic Level Control) threshold ( R118 ). Backing these off slightly will warm up your transmitted voice audio significantly. 4. Interfacing for Digital Modes (FT8, JS8Call, Winlink)
To allow programming of memory banks A and B (which are often factory-locked), ensure jumper W33 (W1033) is not installed.
The primary goal for ham operators is to unlock the radio's frequency flexibility and improve its interface for non-marine use.
The Ultimate Guide to Icom IC-M700 Mods: Expanding Your Marine HF Transceiver
HM-180 8Pin Microphone Speaker Mic for ICOM IC-M700 IC-M710 IC-M600 Radio | Made in China | Clip
: Hosts a collection of over 100 Icom modification documents , including specific guides for the M700's power and lock-out settings. Go to product viewer dialog for this item.
Achieving this requires modifying the radio. This guide covers the most popular modifications for the Icom IC-M700, including general coverage transmit (MARS/CAP/Ham bands), audio improvements, and power adjustments.
Access the main control/logic circuit board, usually located behind the front panel or under the top cover, depending on the specific production run (M700 vs. M700PRO).
The Icom IC-M700 is a classic marine SSB transceiver that is highly popular for amateur (Ham) radio conversion. Modifying it typically involves , expanding memory , and improving audio for non-marine use. 📻 Core Modifications for Ham Radio
This mod requires adding a modern, standalone noise blanker between the IF output and the audio amp (a "Tiny Noise Blanker" board from eBay or a homebrew design). However, a simpler "soft-mod" exists:
Are you planning to use it for or digital modes (FT8/Winlink) ? Share public link
: By clipping the line that senses the Push-To-Talk (PTT) switch on the Clarifier circuit and tying it to a constant 8V DC source inside the radio, the Clarifier will remain active during transmission. This allows you to "net" perfectly onto an amateur radio frequency. 3. Microphone Audio & Compression Upgrades
The Ultimate Guide to Icom IC-M700 Modifications The Icom IC-M700 is a legendary marine HF transceiver. Built like a tank, this commercial-grade radio is famous for its reliability. While designed for maritime use, many amateur radio operators and shortwave enthusiasts use it on ham bands.
On the Low-Pass Filter unit (near the PA), locate R28 . This resistor sets the ALC threshold. Replace the stock value (often 22k ohms) with a 50k ohm linear potentiometer in series with a 10k ohm fixed resistor.
If over-modulation or "splatter" becomes an issue after changing microphones, you can adjust the internal Mic Gain potentiometer () and the ALC (Automatic Level Control) threshold ( R118 ). Backing these off slightly will warm up your transmitted voice audio significantly. 4. Interfacing for Digital Modes (FT8, JS8Call, Winlink)
To allow programming of memory banks A and B (which are often factory-locked), ensure jumper W33 (W1033) is not installed.
The primary goal for ham operators is to unlock the radio's frequency flexibility and improve its interface for non-marine use.
The Ultimate Guide to Icom IC-M700 Mods: Expanding Your Marine HF Transceiver
HM-180 8Pin Microphone Speaker Mic for ICOM IC-M700 IC-M710 IC-M600 Radio | Made in China | Clip
: Hosts a collection of over 100 Icom modification documents , including specific guides for the M700's power and lock-out settings. Go to product viewer dialog for this item.
Achieving this requires modifying the radio. This guide covers the most popular modifications for the Icom IC-M700, including general coverage transmit (MARS/CAP/Ham bands), audio improvements, and power adjustments.
Access the main control/logic circuit board, usually located behind the front panel or under the top cover, depending on the specific production run (M700 vs. M700PRO).
The Icom IC-M700 is a classic marine SSB transceiver that is highly popular for amateur (Ham) radio conversion. Modifying it typically involves , expanding memory , and improving audio for non-marine use. 📻 Core Modifications for Ham Radio
This mod requires adding a modern, standalone noise blanker between the IF output and the audio amp (a "Tiny Noise Blanker" board from eBay or a homebrew design). However, a simpler "soft-mod" exists:
Are you planning to use it for or digital modes (FT8/Winlink) ? Share public link
English 
中文 (中国) 
한국어 
Русский 
